收藏本站
W971GG6JB
9.2
Clock Enable (CKE) Truth Table for Synchronous Transitions
STATE
COMMAND (N)
CURRENT
2
Previous Cycle
(N-1)
CKE
1
Current Cycle
(N)
1
3
RAS , CAS , W E , CS
ACTION (N)
3
NOTES
L
L
X
Maintain Power Down
11, 13, 15
Power Down
L
L
H
L
DESELECT or NOP
X
Power Down Exit
Maintain Power Down
4, 8, 11, 13
11, 15, 16
Self Refresh
L
H
DESELECT or NOP
Self Refresh Exit
4, 5, 9, 16
Bank(s) Active
All Banks Idle
H
H
H
L
L
L
DESELECT or NOP
DESELECT or NOP
REFRESH
Active Power Down
Entry
Precharge Power Down
Entry
Self Refresh Entry
4, 8, 10, 11,
13
4, 8, 10, 11,
13
6, 9, 11, 13
H
H
Refer to the Command Truth Table
7
Notes:
1. CKE (N) is the logic state of CKE at clock edge N; CKE (N – 1) was the state of CKE at the previous clock edge.
2. Current state is the state of the DDR2 SDRAM immediately prior to clock edge N.
3. COMMAND (N) is the command registered at clock edge N, and ACTION (N) is a result of COMMAND (N).
4. All states and sequences not shown are illegal or reserved unless explicitly described elsewhere in this document.
5. On Self Refresh Exit DESELECT or NOP commands must be issued on every clock edge occurring during the t XSNR period.
Read commands may be issued only after t XSRD (200 clocks) is satisfied.
6. Self Refresh mode can only be entered from the All Banks Idle state.
7. Must be a legal command as defined in the Command Truth Table.
8. Valid commands for Power Down Entry and Exit are NOP and DESELECT only.
9. Valid commands for Self Refresh Exit are NOP and DESELECT only.
10. Power Down and Self Refresh can not be entered while Read or Write operations, (Extended) Mode Register Set
operations or Precharge operations are in progress. See section 8.9 “ Power Down Mode ” and section 8.3.7/8.3.8 “ Self
Refresh Entry Command/Self Refresh Exit Command ” for a detailed list of restrictions.
11. tCKEmin of 3 clocks means CKE must be registered on three consecutive positive clock edges. CKE must remain at the
valid input level the entire time it takes to achieve the 3 clocks of registration. Thus, after any CKE transition, CKE may not
transition from its valid level during the time period of t IS + 2 x t CK + t IH .
12. The state of ODT does not affect the states described in this table. The ODT function is not available during Self Refresh.
See section 8.2.4.
13. The Power Down does not perform any refresh operations. The duration of Power Down Mode is therefore limited by the
refresh requirements outlined in section 8.9.
14. CKE must be maintained HIGH while the SDRAM is in OCD calibration mode.
15. “X” means “don?t care (including floating around V REF )” in Self Refresh and Power Down. However ODT must be driven
high or low in Power Down if the ODT function is enabled (Bit A2 or A6 set to “1” in EMR (1)).
16. V REF must be maintained during Self Refresh operation.
9.3
Data Mask (DM) Truth Table
FUNCTION
Write enable
Write inhibit
DM
L
H
DQS
Valid
X
NOTE
1
1
Note:
1. Used to mask write data, provided coincident with the corresponding data.
Publication Release Date: Sep. 24, 2013
- 32 -
Revision A09
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
W971GG8JB-25 IC DDR2 SDRAM 1GBIT 60WBGA
W9725G6IB-25 IC DDR2-800 SDRAM 256MB 84-WBGA
W9725G6JB25I IC DDR2 SDRAM 256MBIT 84WBGA
W9725G6KB-25I IC DDR2 SDRAM 256MBIT 84WBGA
W972GG6JB-3I IC DDR2 SDRAM 2GBITS 84WBGA
W9751G6IB-25 IC DDR2-800 SDRAM 512MB 84-WBGA
W9751G6KB-25 IC DDR2 SDRAM 512MBIT 84WBGA
W9812G6JH-6I IC SDRAM 128MBIT 54TSOPII
相关代理商/技术参数
W971GG6JB-25I 制造商:Winbond Electronics 功能描述:-40~85 1GB DDR2 FOR INDUSTRY
W971GG6JB25ITR 制造商:Winbond Electronics Corp 功能描述:1G, DDR2-800, X16, IND TEMP
W971GG6JB25TR 制造商:Winbond Electronics Corp 功能描述:NR, DDR2-800, X16
W971GG6JB-3 制造商:Winbond Electronics Corp 功能描述:1GBIT DDRII
W971GG6KB-18 制造商:Winbond Electronics Corp 功能描述:1G, DDR2-1066, X16 制造商:Winbond Electronics Corp 功能描述:IC MEMORY
W971GG8JB 制造商:WINBOND 制造商全称:Winbond 功能描述:16M × 8 BANKS × 8 BIT DDR2 SDRAM
W971GG8JB-25 功能描述:IC DDR2 SDRAM 1GBIT 60WBGA RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:72 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 同步 存储容量:4.5M（256K x 18） 速度:133MHz 接口:并联 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 封装/外壳:100-LQFP 供应商设备封装:100-TQFP（14x20） 包装:托盘
W9725G6IB-25 功能描述:IC DDR2-800 SDRAM 256MB 84-WBGA RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1,000 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:4K (512 x 8) 速度:400kHz 接口:I²C，2 线串口 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.173"，4.40mm 宽） 供应商设备封装:8-MFP 包装:带卷 (TR)